JNX-L2TP-MIB DEFINITIONS::=BEGINIMPORTSInteger32,Unsigned32,Counter32,Gauge32,Counter64,TimeTicks, transmission,MODULE-IDENTITY,
OBJECT-TYPE,NOTIFICATION-TYPEFROM SNMPv2-SMI
DateAndTime,RowStatus,StorageType,TEXTUAL-CONVENTION,TruthValueFROM SNMPv2-TC
CounterBasedGauge64-- RFC 2856FROM HCNUM-TC
InetAddress,InetAddressType,InetPortNumberFROM INET-ADDRESS-MIB
SnmpAdminStringFROM SNMP-FRAMEWORK-MIB
OBJECT-GROUP,MODULE-COMPLIANCE,NOTIFICATION-GROUPFROM SNMPv2-CONF
jnxL2tpMibRoot
FROM JUNIPER-SMI;jnxL2tp MODULE-IDENTITYLAST-UPDATED"200701110000Z"-- 11 January 2007
ORGANIZATION"Juniper Networks Inc."CONTACT-INFO" Juniper Technical Assistance Center
Juniper Networks, Inc.
1194 N. Mathilda Avenue
Sunnyvale, CA 94089
E-mail: support@juniper.net"DESCRIPTION"Provides monitoring information regarding
the Layer Two Transport Protocol. This MIB
is based on the standard MIB defined in
RFC 3371. However, there are significant differences
including the INDEX fields of l2tpTunnelStatsTable
and l2tpSessionStatsTable."-- revision logREVISION"200701110000Z"-- 11 January 2007DESCRIPTION"Initial revision."::={ jnxL2tpMibRoot 1}---- Definitions of significant branches--jnxL2tpObjects OBJECTIDENTIFIER::={ jnxL2tp 1}
jnxL2tpScalar OBJECTIDENTIFIER::={ jnxL2tpObjects 1}jnxL2tpStats OBJECTIDENTIFIER::={ jnxL2tpScalar 1}---- The L2TP Scalar Status and Statistics Group--jnxL2tpStatsTotalTunnels OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the total number of tunnels
that are currently in the established state. This is
an instantaneously accumulated value which can increase
or decrease depending on number of tunnels established
at the time of querying."::={ jnxL2tpStats 1}jnxL2tpStatsTotalSessions OBJECT-TYPE
SYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the total number of sessions
that are currently in the established state. This is
an instantaneously accumulated value which can increase
or decrease depending on number of tunnels established
at the time of querying."::={ jnxL2tpStats 2}jnxL2tpStatsControlRxOctets OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the number of control channel
octets received by the existing tunnels. This is
an instantaneously accumulated value which can increase
or decrease depending on number of tunnels established
at the time of querying."::={ jnxL2tpStats 3}
jnxL2tpStatsControlRxPkts OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the number of control packets
received by the existing tunnels. This is an
instantaneously accumulated value which can increase
or decrease depending on number of tunnels established
at the time of querying."::={ jnxL2tpStats 4}jnxL2tpStatsControlTxOctets OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the number of control channel
octets that were transmitted to the existing tunnel
endpoints. This is an instantaneously accumulated
value which can increase or decrease depending on
number of tunnels established at the time of querying."
::={ jnxL2tpStats 5}jnxL2tpStatsControlTxPkts OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the number of control packets
that were transmitted to the existing tunnel endpoints.This
is an instantaneously accumulated value which can increase
or decrease depending on number of tunnels established
at the time of querying."::={ jnxL2tpStats 6}jnxL2tpStatsPayloadRxOctets OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the number of payload channel
octets that were received on the exisiting tunnels. This is
an instantaneously accumulated value which can increase
or decrease depending on number of tunnels established
at the time of querying."::={ jnxL2tpStats 7}jnxL2tpStatsPayloadRxPkts OBJECT-TYPESYNTAXCounterBasedGauge64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the number of payload packets
that were received on the existing tunnels. This is
an instantaneously accumulated value which can increase
or decrease depending on number of tunnels established
at the time of querying."::={ jnxL2tpStats 8}jnxL2tpStatsPayloadTxOctets OBJECT-TYPESYNTAXCounterBasedGauge64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the number of payload channel
octets that were transmitted to the existing tunnel peers.
This is an instantaneously accumulated value which can
increase or decrease depending on number of tunnels
established at the time of querying."::={ jnxL2tpStats 9}jnxL2tpStatsPayloadTxPkts OBJECT-TYPESYNTAXCounterBasedGauge64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the number of payload packets
that were transmitted to existing tunnel peers. This is
an instantaneously accumulated value which can increase
or decrease depending on number of tunnels established
at the time of querying."::={ jnxL2tpStats 10}jnxL2tpStatsErrorTxPkts OBJECT-TYPESYNTAXCounterBasedGauge64MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object returns the number of errored packet
transmission attempts to the existing tunnel peers. This is
an instantaneously accumulated value which can increase
or decrease depending on number of tunnels established
at the time of querying."::={ jnxL2tpStats 11}jnxL2tpStatsErrorRxPkts OBJECT-TYPESYNTAXCounterBasedGauge64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the number of errored packets
that were received from the existing tunnel peers. This is
an instantaneously accumulated value which can increase
or decrease depending on number of tunnels established
at the time of querying."::={ jnxL2tpStats 12}---- The L2TP Tunnel Group Status and Statistics Table--jnxL2tpTunnelGroupStatsTable OBJECT-TYPE
SYNTAXSEQUENCEOF JnxL2tpTunnelGroupStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The L2TP tunnel group status and statistics table. This
table contains objects that can be used to describe
the current status and statistics of a single L2TP
tunnel group."::={ jnxL2tpObjects 2}jnxL2tpTunnelGroupStatsEntry OBJECT-TYPESYNTAX JnxL2tpTunnelGroupStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An L2TP tunnel group stats entry."INDEX{IMPLIED jnxL2tpTunnelGroupStatsTnlGrpName }::={ jnxL2tpTunnelGroupStatsTable 1}
JnxL2tpTunnelGroupStatsEntry ::=SEQUENCE{
jnxL2tpTunnelGroupStatsTnlGrpName
OCTETSTRING,
jnxL2tpTunnelGroupStatsGatewayAddrType
InetAddressType,
jnxL2tpTunnelGroupStatsGatewayAddr
InetAddress,
jnxL2tpTunnelGroupStatsSvcIntfName
SnmpAdminString,
jnxL2tpTunnelGroupStatsTotalTunnels
Gauge32,
jnxL2tpTunnelGroupStatsTotalSessions
Gauge32}jnxL2tpTunnelGroupStatsTnlGrpName OBJECT-TYPESYNTAXOCTETSTRING(SIZE(1..128))MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object contains the name of this tunnel
group."::={ jnxL2tpTunnelGroupStatsEntry 1}jnxL2tpTunnelGroupStatsGatewayAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the type of local IP address
for L2TP tunnels that are part of this group."::={ jnxL2tpTunnelGroupStatsEntry 2}jnxL2tpTunnelGroupStatsGatewayAddr OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the local IP address
for L2TP tunnels that are part of this group."::={ jnxL2tpTunnelGroupStatsEntry 3}
jnxL2tpTunnelGroupStatsSvcIntfName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the name of the service
interface that is hosting this tunnel group."::={ jnxL2tpTunnelGroupStatsEntry 4}jnxL2tpTunnelGroupStatsTotalTunnels OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the total number of tunnels
that are currently in the established state in this
tunnel group."::={ jnxL2tpTunnelGroupStatsEntry 5}jnxL2tpTunnelGroupStatsTotalSessions OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-only
STATUScurrentDESCRIPTION"This object returns the total number of sessions
that are currently in the established state in
this tunnel group."::={ jnxL2tpTunnelGroupStatsEntry 6}---- The L2TP Tunnel Status and Statistics Table--jnxL2tpTunnelStatsTable OBJECT-TYPESYNTAXSEQUENCEOF JnxL2tpTunnelStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The L2TP tunnel status and statistics table. This
table contains objects that can be used to describe
the current status and statistics of a single L2TP
tunnel."::={ jnxL2tpObjects 3}jnxL2tpTunnelStatsEntry OBJECT-TYPESYNTAX JnxL2tpTunnelStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An L2TP tunnel interface stats entry."INDEX{ jnxL2tpTunnelStatsLocalTID }::={ jnxL2tpTunnelStatsTable 1}
JnxL2tpTunnelStatsEntry ::=SEQUENCE{
jnxL2tpTunnelStatsLocalTID
Integer32,
jnxL2tpTunnelStatsServiceInterface
SnmpAdminString,
jnxL2tpTunnelStatsTunnelGroup
SnmpAdminString,
jnxL2tpTunnelStatsRemoteTID
Integer32,
jnxL2tpTunnelStatsRemoteIpAddrType
InetAddressType,
jnxL2tpTunnelStatsRemoteIpAddress
InetAddress,
jnxL2tpTunnelStatsRemoteUdpPort
InetPortNumber,
jnxL2tpTunnelStatsActiveSessions
Gauge32,
jnxL2tpTunnelStatsState
INTEGER,
jnxL2tpTunnelStatsLocalIpAddrType
InetAddressType,
jnxL2tpTunnelStatsLocalIpAddress
InetAddress,
jnxL2tpTunnelStatsLocalUdpPort
InetPortNumber,
jnxL2tpTunnelStatsLocalHostName
SnmpAdminString,
jnxL2tpTunnelStatsRemoteHostName
SnmpAdminString,
jnxL2tpTunnelMaxSessions
Integer32,
jnxL2tpTunnelStatsWindowSize
Integer32,
jnxL2tpTunnelStatsHelloInterval
Integer32,
jnxL2tpTunnelStatsCreationTime
DateAndTime,
jnxL2tpTunnelStatsUpTime
TimeTicks,
jnxL2tpTunnelStatsIdleTime
TimeTicks,
jnxL2tpTunnelStatsCollectionStart
DateAndTime,
jnxL2tpTunnelStatsControlTxPkts
Counter32,
jnxL2tpTunnelStatsControlTxBytes
Counter64,
jnxL2tpTunnelStatsControlRxPkts
Counter32,
jnxL2tpTunnelStatsControlRxBytes
Counter64,
jnxL2tpTunnelStatsDataTxPkts
Counter32,
jnxL2tpTunnelStatsDataTxBytes
Counter64,
jnxL2tpTunnelStatsDataRxPkts
Counter32,
jnxL2tpTunnelStatsDataRxBytes
Counter64,
jnxL2tpTunnelStatsErrorTxPkts
Counter32,
jnxL2tpTunnelStatsErrorRxPkts
Counter32}jnxL2tpTunnelStatsLocalTID OBJECT-TYPESYNTAXInteger32(0..65535)
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object contains the local tunnel Identifier."REFERENCE"RFC 2661, Section 3.1"::={ jnxL2tpTunnelStatsEntry 1}jnxL2tpTunnelStatsServiceInterface OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the name of the service
interface on which this tunnel is being hosted."::={ jnxL2tpTunnelStatsEntry 2}jnxL2tpTunnelStatsTunnelGroup OBJECT-TYPESYNTAXSnmpAdminString
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the name of the tunnel
group that this tunnel is part of."::={ jnxL2tpTunnelStatsEntry 3}jnxL2tpTunnelStatsRemoteTID OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the remote tunnel Identifier."REFERENCE"RFC 2661, Section 3.1"::={ jnxL2tpTunnelStatsEntry 4}jnxL2tpTunnelStatsRemoteIpAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-only
STATUScurrentDESCRIPTION"This object contains the type of the remote end
address of this tunnel."::={ jnxL2tpTunnelStatsEntry 5}jnxL2tpTunnelStatsRemoteIpAddress OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the remote end address
of this tunnel."::={ jnxL2tpTunnelStatsEntry 6}jnxL2tpTunnelStatsRemoteUdpPort OBJECT-TYPESYNTAXInetPortNumberMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the remote end UDP
port of this tunnel."::={ jnxL2tpTunnelStatsEntry 7}
jnxL2tpTunnelStatsActiveSessions OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the total number of sessions
in the established state for this tunnel."::={ jnxL2tpTunnelStatsEntry 8}jnxL2tpTunnelStatsState OBJECT-TYPESYNTAXINTEGER{cc-responder-accept-new(1),cc-responder-reject-new(2),cc-responder-idle(3),cc-responder-wait-ctl-conn(4),cleanup(5),
closed(6),destroyed(7),established(8),terminate(9),unknown(10)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This field contains the current state of the
control tunnel - one of the internal tunnel
state names as described below:
cc_responder_accept_new
The tunnel has received and accepted the start
control connection request (SCCRQ)
cc_responder_reject_new
The tunnel has received and rejected the SCCRQ
cc_responder_idle
The tunnel has just been created
cc_responder_wait_ctl_conn
The tunnel has sent the start control connection
response (SCCRP) and is waiting for the start
control connection connected (SCCCN) message
cleanup
The tunnel is being cleaned up
closed
The tunnel is being closed
destroyed
The tunnel is being destroyed
established
The tunnel is operating
terminate
The tunnel is terminating
Unknown
The tunnel is not connected to the router."::={ jnxL2tpTunnelStatsEntry 9}jnxL2tpTunnelStatsLocalIpAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the type of the local
end address of this tunnel."::={ jnxL2tpTunnelStatsEntry 10}jnxL2tpTunnelStatsLocalIpAddress OBJECT-TYPESYNTAXInetAddress
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the local end address
of this tunnel."::={ jnxL2tpTunnelStatsEntry 11}jnxL2tpTunnelStatsLocalUdpPort OBJECT-TYPESYNTAXInetPortNumberMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the local end UDP port
of this tunnel."::={ jnxL2tpTunnelStatsEntry 12}jnxL2tpTunnelStatsLocalHostName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the local host name
of this tunnel."::={ jnxL2tpTunnelStatsEntry 13}jnxL2tpTunnelStatsRemoteHostName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the host name as discovered
during the tunnel establishment phase (via the Host
Name AVP) of the L2TP peer. If the tunnel is idle
this object should maintain its value from the last
time it was connected."::={ jnxL2tpTunnelStatsEntry 14}jnxL2tpTunnelMaxSessions OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the maximum number of sessions
configured on this tunnel. It could be any positive
number or unlimited (0)."::={ jnxL2tpTunnelStatsEntry 15}jnxL2tpTunnelStatsWindowSize OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the send window size for this
tunnel."::={ jnxL2tpTunnelStatsEntry 16}jnxL2tpTunnelStatsHelloInterval OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the hello interval for this
tunnel."::={ jnxL2tpTunnelStatsEntry 17}jnxL2tpTunnelStatsCreationTime OBJECT-TYPESYNTAXDateAndTimeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the time of creation of
this tunnel."::={ jnxL2tpTunnelStatsEntry 18}jnxL2tpTunnelStatsUpTime OBJECT-TYPESYNTAXTimeTicksMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the time elapsed
since this tunnel was established."::={ jnxL2tpTunnelStatsEntry 19}jnxL2tpTunnelStatsIdleTime OBJECT-TYPESYNTAXTimeTicks
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the time elapsed
since this tunnel had last data activity
(transmission or reception)."::={ jnxL2tpTunnelStatsEntry 20}jnxL2tpTunnelStatsCollectionStart OBJECT-TYPESYNTAXDateAndTimeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the time at which the
statistics gathering started for this tunnel."::={ jnxL2tpTunnelStatsEntry 21}jnxL2tpTunnelStatsControlTxPkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object contains the number of control
packets that were transmitted to the tunnel
peer."::={ jnxL2tpTunnelStatsEntry 22}jnxL2tpTunnelStatsControlTxBytes OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of control
bytes that were transmitted to the tunnel
peer."::={ jnxL2tpTunnelStatsEntry 23}jnxL2tpTunnelStatsControlRxPkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of control packets
received on the tunnel."
::={ jnxL2tpTunnelStatsEntry 24}jnxL2tpTunnelStatsControlRxBytes OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of control
bytes that were received from the tunnel
peer."::={ jnxL2tpTunnelStatsEntry 25}jnxL2tpTunnelStatsDataTxPkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of data packets
transmitted to the tunnel."::={ jnxL2tpTunnelStatsEntry 26}jnxL2tpTunnelStatsDataTxBytes OBJECT-TYPE
SYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of data
bytes that were transmitted to the tunnel
peer."::={ jnxL2tpTunnelStatsEntry 27}jnxL2tpTunnelStatsDataRxPkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of data packets
received from this tunnel."::={ jnxL2tpTunnelStatsEntry 28}jnxL2tpTunnelStatsDataRxBytes OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object contains the number of data
bytes that were received from the tunnel
peer."::={ jnxL2tpTunnelStatsEntry 29}jnxL2tpTunnelStatsErrorTxPkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of error
transmit packets on the tunnel."::={ jnxL2tpTunnelStatsEntry 30}jnxL2tpTunnelStatsErrorRxPkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of error
receive packets on the tunnel."::={ jnxL2tpTunnelStatsEntry 31}
---- The L2TP Session Status and Statistics Table--jnxL2tpSessionStatsTable OBJECT-TYPESYNTAXSEQUENCEOF JnxL2tpSessionStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The L2TP session status and statistics table. This
table contains the objects that can be used to
describe the current status and statistics of a
single L2TP tunneled session."::={ jnxL2tpObjects 4}jnxL2tpSessionStatsEntry OBJECT-TYPESYNTAX JnxL2tpSessionStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An L2TP session interface stats entry."INDEX{ jnxL2tpSessionStatsLocalTID,
jnxL2tpSessionStatsLocalSID }::={ jnxL2tpSessionStatsTable 1}
JnxL2tpSessionStatsEntry ::=SEQUENCE{
jnxL2tpSessionStatsLocalTID
Integer32,
jnxL2tpSessionStatsLocalSID
Integer32,
jnxL2tpSessionStatsServiceInterface
SnmpAdminString,
jnxL2tpSessionStatsTunnelGroup
SnmpAdminString,
jnxL2tpSessionStatsRemoteSID
Integer32,
jnxL2tpSessionStatsInterfaceUnit
Integer32,
jnxL2tpSessionStatsEncapType
INTEGER,
jnxL2tpSessionStatsBundleID
Integer32,
jnxL2tpSessionStatsState
INTEGER,
jnxL2tpSessionStatsUserName
SnmpAdminString,
jnxL2tpSessionStatsMode
INTEGER,
jnxL2tpSessionStatsLocalAddrType
InetAddressType,
jnxL2tpSessionStatsLocalAddress
InetAddress,
jnxL2tpSessionStatsLocalUdpPort
InetPortNumber,
jnxL2tpSessionStatsRemoteAddrType
InetAddressType,
jnxL2tpSessionStatsRemoteAddress
InetAddress,
jnxL2tpSessionStatsRemoteUdpPort
InetPortNumber,
jnxL2tpSessionStatsLocalHostName
SnmpAdminString,
jnxL2tpSessionStatsRemoteHostName
SnmpAdminString,
jnxL2tpSessionAssignedIpAddrType
InetAddressType,
jnxL2tpSessionAssignedIpAddress
InetAddress,
jnxL2tpSessionLocalMRU
INTEGER,
jnxL2tpSessionRemoteMRU
INTEGER,
jnxL2tpSessionStatsTxSpeed
Unsigned32,
jnxL2tpSessionStatsRxSpeed
Unsigned32,
jnxL2tpSessionStatsCallBearerType
INTEGER,
jnxL2tpSessionStatsFramingType
INTEGER,
jnxL2tpSessionStatsLCPRenegotiation
INTEGER,
jnxL2tpSessionStatsAuthMethod
INTEGER,
jnxL2tpSessionStatsNasIpAddrType
InetAddressType,
jnxL2tpSessionStatsNasIpAddress
InetAddress,
jnxL2tpSessionStatsNasIpPort
InetPortNumber,
jnxL2tpSessionStatsFramedProtocol
INTEGER,
jnxL2tpSessionStatsFramedIpAddrType
InetAddressType,
jnxL2tpSessionStatsFramedIpAddress
InetAddress,
jnxL2tpSessionStatsCallingStationID
SnmpAdminString,
jnxL2tpSessionStatsCalledStationID
SnmpAdminString,
jnxL2tpSessionStatsAcctDelayTime
Integer32,
jnxL2tpSessionStatsAcctSessionID
SnmpAdminString,
jnxL2tpSessionStatsAcctMethod
INTEGER,
jnxL2tpSessionStatsAcctSessionTime
Gauge32,
jnxL2tpSessionStatsAcctNasPortType
INTEGER,
jnxL2tpSessionStatsAcctTnlClientEndPoint
Integer32,
jnxL2tpSessionStatsAcctTnlServerEndPoint
Integer32,
jnxL2tpSessionStatsAcctTnlClientAuthID
SnmpAdminString,
jnxL2tpSessionStatsAcctTnlServerAuthID
SnmpAdminString,
jnxL2tpSessionStatsUserProfileName
SnmpAdminString,
jnxL2tpSessionStatsInterfaceID
SnmpAdminString,
jnxL2tpSessionStatsCallSerialNumber
Unsigned32,
jnxL2tpSessionStatsCreationTime
DateAndTime,
jnxL2tpSessionStatsUpTime
TimeTicks,
jnxL2tpSessionStatsIdleTime
TimeTicks,
jnxL2tpSessionStatsCollectionStart
DateAndTime,
jnxL2tpSessionStatsControlTxPkts
Counter32,
jnxL2tpSessionStatsControlTxBytes
Counter64,
jnxL2tpSessionStatsControlRxPkts
Counter32,
jnxL2tpSessionStatsControlRxBytes
Counter64,
jnxL2tpSessionStatsDataTxPkts
Counter32,
jnxL2tpSessionStatsDataTxBytes
Counter64,
jnxL2tpSessionStatsDataRxPkts
Counter32,
jnxL2tpSessionStatsDataRxBytes
Counter64,
jnxL2tpSessionStatsErrorTxPkts
Counter32,
jnxL2tpSessionStatsErrorRxPkts
Counter32}jnxL2tpSessionStatsLocalTID OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object contains the local tunnel Identifier."REFERENCE"RFC 2661, Section 3.1"::={ jnxL2tpSessionStatsEntry 1}jnxL2tpSessionStatsLocalSID OBJECT-TYPESYNTAXInteger32(0..65535)
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object contains the local session Identifier."REFERENCE"RFC 2661, Section 3.1"::={ jnxL2tpSessionStatsEntry 2}jnxL2tpSessionStatsServiceInterface OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the name of the service
interface on which this session is being hosted."::={ jnxL2tpSessionStatsEntry 3}jnxL2tpSessionStatsTunnelGroup OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object contains the name of the tunnel
group that this session is part of."::={ jnxL2tpSessionStatsEntry 4}jnxL2tpSessionStatsRemoteSID OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the remote end assigned
session identifier for this session. When a session
is starting this value may be zero until the remote
tunnel endpoint has responded."REFERENCE"RFC 2661, Section 3.1"::={ jnxL2tpSessionStatsEntry 5}jnxL2tpSessionStatsInterfaceUnit OBJECT-TYPESYNTAXInteger32(0..65535)
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the interface unit number
corresponding to the logical service interface
on which the session is being hosted."::={ jnxL2tpSessionStatsEntry 6}jnxL2tpSessionStatsEncapType OBJECT-TYPESYNTAXINTEGER{ppp(1),multilink-ppp(2),unknown(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the tunnel encapsulation
type."::={ jnxL2tpSessionStatsEntry 7}jnxL2tpSessionStatsBundleID OBJECT-TYPESYNTAXInteger32(1..65536)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object identifies the bundle that this
session is a link of. This field is valid
only for tunnel encapsulation type multilink-ppp."::={ jnxL2tpSessionStatsEntry 8}jnxL2tpSessionStatsState OBJECT-TYPESYNTAXINTEGER{established(1),closed(2),destroyed(3),
cleanup(4),lns-ic-accept-new(5),lns-ic-idle(6),lns-ic-reject-new(7),lns-ic-wait-connect(8)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This field contains the current state of the
session - one of the internal session related
state names as described below:
established
The session is operating
closed
The session is being closed
destroyed
The session is being destroyed
cleanup
The session is being cleaned up
lns_ic_accept_new
A new session is being accepted
lns_ic_idle
The session has been created and is idle
lns_ic_reject_new
The new session is being rejected
lns_ic_wait_connect
The session is waiting for the peer's incoming
call connected (ICCN) message."::={ jnxL2tpSessionStatsEntry 9}jnxL2tpSessionStatsUserName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object identifies the peer session name on
this interface. This is typically the login name
of the remote user. If the user name is unknown to
the local tunnel peer then this object will contain
a null string."::={ jnxL2tpSessionStatsEntry 10}jnxL2tpSessionStatsMode OBJECT-TYPESYNTAXINTEGER{shared(1),
dedicate(2),unknown(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object identifies the configured mode value for
this session."::={ jnxL2tpSessionStatsEntry 11}jnxL2tpSessionStatsLocalAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the type of the local
end address of the tunnel that is hosting
this session."::={ jnxL2tpSessionStatsEntry 12}
jnxL2tpSessionStatsLocalAddress OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the local end address
of the tunnel that is hosting this session."::={ jnxL2tpSessionStatsEntry 13}jnxL2tpSessionStatsLocalUdpPort OBJECT-TYPESYNTAXInetPortNumberMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the UDP port of the
local end of the tunnel that is hosting
this session."::={ jnxL2tpSessionStatsEntry 14}jnxL2tpSessionStatsRemoteAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-only
STATUScurrentDESCRIPTION"This object contains the type of the remote end
address of the tunnel hosting this session."::={ jnxL2tpSessionStatsEntry 15}jnxL2tpSessionStatsRemoteAddress OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the remote end address
of the tunnel hosting this session."::={ jnxL2tpSessionStatsEntry 16}jnxL2tpSessionStatsRemoteUdpPort OBJECT-TYPESYNTAXInetPortNumberMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the UDP port of the
remote end of the tunnel hosting this session."::={ jnxL2tpSessionStatsEntry 17}jnxL2tpSessionStatsLocalHostName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the local host name
of the tunnel that is hosting this session."::={ jnxL2tpSessionStatsEntry 18}jnxL2tpSessionStatsRemoteHostName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the host name as discovered
during the tunnel establishment phase (via the Host
Name AVP) of the L2TP peer."::={ jnxL2tpSessionStatsEntry 19}
jnxL2tpSessionAssignedIpAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the type of IP address of PPP client
being tunneled as obtained from IPCP configuration
during session establishment."::={ jnxL2tpSessionStatsEntry 20}jnxL2tpSessionAssignedIpAddress OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the IP address of the PPP client
being tunneled as obtained from IPCP configuration
during session establishment."::={ jnxL2tpSessionStatsEntry 21}
jnxL2tpSessionLocalMRU OBJECT-TYPESYNTAXINTEGER(1..2147483647)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The current value of the MRU for the local PPP
Entity. This value is the MRU that the remote
entity is using when sending packets to this
session."::={ jnxL2tpSessionStatsEntry 22}jnxL2tpSessionRemoteMRU OBJECT-TYPESYNTAXINTEGER(1..2147483647)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The current value of the MRU for the remote
PPP Entity. This value is the MRU that the
local entity is using when sending packets to
the remote PPP client."::={ jnxL2tpSessionStatsEntry 23}jnxL2tpSessionStatsTxSpeed OBJECT-TYPESYNTAXUnsigned32UNITS"bits per second"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the last known transmit
baud rate for this session."::={ jnxL2tpSessionStatsEntry 24}jnxL2tpSessionStatsRxSpeed OBJECT-TYPESYNTAXUnsigned32UNITS"bits per second"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns the last known receive
baud rate for this session established."
::={ jnxL2tpSessionStatsEntry 25}jnxL2tpSessionStatsCallBearerType OBJECT-TYPESYNTAXINTEGER{none(1),digital(2),analog(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object describes the bearer type of this
session."::={ jnxL2tpSessionStatsEntry 26}jnxL2tpSessionStatsFramingType OBJECT-TYPESYNTAXINTEGER{none(1),
sync(2),async(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object describes the framing type of this
session."::={ jnxL2tpSessionStatsEntry 27}jnxL2tpSessionStatsLCPRenegotiation OBJECT-TYPESYNTAXINTEGER{off(1),on(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object returns whether LCP renegotiation
is on or off for this session."::={ jnxL2tpSessionStatsEntry 28}jnxL2tpSessionStatsAuthMethod OBJECT-TYPESYNTAXINTEGER{none(1),text(2),pppChap(3),pppPap(4),pppEap(5),pppMsChapV1(6),pppMsChapV2(7),other(8)}MAX-ACCESSread-only
STATUScurrentDESCRIPTION"This object contains the proxy authentication
method employed by the LAC for the session."::={ jnxL2tpSessionStatsEntry 29}jnxL2tpSessionStatsNasIpAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the type of IP address of the RADIUS
network address server to which the accounting
records for this session are being sent to."::={ jnxL2tpSessionStatsEntry 30}jnxL2tpSessionStatsNasIpAddress OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"This object contains the IP address of the RADIUS
network address server to which the accounting
records for this session are being sent to."::={ jnxL2tpSessionStatsEntry 31}jnxL2tpSessionStatsNasIpPort OBJECT-TYPESYNTAXInetPortNumberMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the port on which RADIUS
network address server accounting messages will
be sent."::={ jnxL2tpSessionStatsEntry 32}jnxL2tpSessionStatsFramedProtocol OBJECT-TYPESYNTAXINTEGER{ppp(1),slip(2),arap(3),
gandalf(4),xylogicsIPX-SLIP(5),x75-sync(6),none(100)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the frame protocol attribute
obtained from RADIUS server for this session."REFERENCE"RFC 2865, Section 5.7"::={ jnxL2tpSessionStatsEntry 33}jnxL2tpSessionStatsFramedIpAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This Attribute indicates the type of address to be
configured for the user, as provided by the
RADIUS server in response to authentication request."REFERENCE"RFC 2865, Section 5.8"::={ jnxL2tpSessionStatsEntry 34}jnxL2tpSessionStatsFramedIpAddress OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This Attribute indicates the address to be
configured for the user, as provided by the
RADIUS server in response to authentication request."REFERENCE"RFC 2865, Section 5.8"::={ jnxL2tpSessionStatsEntry 35}jnxL2tpSessionStatsCallingStationID OBJECT-TYPESYNTAXSnmpAdminString
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This Attribute allows the RADIUS NAS to send in the
Access-Request packet the phone number that the
call came from, using Automatic Number
Identification (ANI) or similar technology.
It is only used in Access-Request packets."REFERENCE"RFC 2865, Section 5.31"::={ jnxL2tpSessionStatsEntry 36}jnxL2tpSessionStatsCalledStationID OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This Attribute allows the RADIUS NAS to send in the
Access-Request packet the phone number that the
user called, using Dialed Number Identification
(DNIS) or similar technology. It is only used in
Access-Request packets."REFERENCE"RFC 2865, Section 5.30"
::={ jnxL2tpSessionStatsEntry 37}jnxL2tpSessionStatsAcctDelayTime OBJECT-TYPESYNTAXInteger32(0..64)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This attribute indicates how many seconds the
RADIUS accounting client has been trying
to send a record for, and can be subtracted from the
time of arrival on the server to find the
approximate time of the event generating this
Accounting-Request."REFERENCE"RFC 2866, Section 5.2"::={ jnxL2tpSessionStatsEntry 38}jnxL2tpSessionStatsAcctSessionID OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-only
STATUScurrentDESCRIPTION"This attribute is a unique Accounting ID to make
it easy to match start and stop records in a log
file."REFERENCE"RFC 2866, Section 5.5"::={ jnxL2tpSessionStatsEntry 39}jnxL2tpSessionStatsAcctMethod OBJECT-TYPESYNTAXINTEGER{radius(1),local(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the accounting method
employed for this session."::={ jnxL2tpSessionStatsEntry 40}jnxL2tpSessionStatsAcctSessionTime OBJECT-TYPE
SYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This attribute indicates how many seconds the
user has received service for."REFERENCE"RFC 2866, Section 5.7"::={ jnxL2tpSessionStatsEntry 41}jnxL2tpSessionStatsAcctNasPortType OBJECT-TYPESYNTAXINTEGER{async(1),sync(2),isdn-sync(3),isdn-asunc-v-120(4),isdn-async-v-110(5),
virtual(6),piafs(7),hdlc-clear-channel(8),x-25(9),x-75(10),g-3-fax(11),sdsl(12),adsl-cap(13),adsl-dmt(14),idsl(15),ethernet(16),xdsl(17),
cable(18),wireless-other(19),wireless-ieee-802-1(20)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This Attribute indicates the type of the physical
port of the NAS which is performing accounting for
the user."REFERENCE"RFC 2865, Section 5.41"::={ jnxL2tpSessionStatsEntry 42}jnxL2tpSessionStatsAcctTnlClientEndPoint OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object contains the remote tunnel Identifier of
the tunnel hosting this session."REFERENCE"RFC 2661, Section 3.1"::={ jnxL2tpSessionStatsEntry 43}jnxL2tpSessionStatsAcctTnlServerEndPoint OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the local tunnel Identifier of
the tunnel hosting this session."REFERENCE"RFC 2661, Section 3.1"::={ jnxL2tpSessionStatsEntry 44}jnxL2tpSessionStatsAcctTnlClientAuthID OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-only
STATUScurrentDESCRIPTION"This object contains the host name as discovered
during the tunnel establishment phase (via the Host
Name AVP) of the L2TP peer, for the tunnel that is
hosting this session."::={ jnxL2tpSessionStatsEntry 45}jnxL2tpSessionStatsAcctTnlServerAuthID OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the local host name
of the tunnel that is hosting this session."::={ jnxL2tpSessionStatsEntry 46}jnxL2tpSessionStatsUserProfileName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object contains the configured access
profile name that is being used for this session."::={ jnxL2tpSessionStatsEntry 47}jnxL2tpSessionStatsInterfaceID OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the interface identification
(name) for the session bearing service interface."::={ jnxL2tpSessionStatsEntry 48}jnxL2tpSessionStatsCallSerialNumber OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the serial number that has
been assigned to this session."::={ jnxL2tpSessionStatsEntry 49}jnxL2tpSessionStatsCreationTime OBJECT-TYPESYNTAXDateAndTimeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the time of creation of
this session."::={ jnxL2tpSessionStatsEntry 50}jnxL2tpSessionStatsUpTime OBJECT-TYPESYNTAXTimeTicksMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the time elapsed
since this session was established."::={ jnxL2tpSessionStatsEntry 51}jnxL2tpSessionStatsIdleTime OBJECT-TYPE
SYNTAXTimeTicksMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the time elapsed
since this session had last data activity
(transmission or reception)."::={ jnxL2tpSessionStatsEntry 52}jnxL2tpSessionStatsCollectionStart OBJECT-TYPESYNTAXDateAndTimeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the time at which the
statistics gathering started for this session."::={ jnxL2tpSessionStatsEntry 53}jnxL2tpSessionStatsControlTxPkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-only
STATUScurrentDESCRIPTION"This object contains the number of control
packets that were transmitted to the session
peer."::={ jnxL2tpSessionStatsEntry 54}jnxL2tpSessionStatsControlTxBytes OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of control
bytes that were transmitted to the session
peer."::={ jnxL2tpSessionStatsEntry 55}jnxL2tpSessionStatsControlRxPkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of control packets
received on the session."::={ jnxL2tpSessionStatsEntry 56}jnxL2tpSessionStatsControlRxBytes OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of control
bytes that were received from the session
peer."::={ jnxL2tpSessionStatsEntry 57}jnxL2tpSessionStatsDataTxPkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of data packets
transmitted to the remote session peer."::={ jnxL2tpSessionStatsEntry 58}
jnxL2tpSessionStatsDataTxBytes OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of data
bytes that were transmitted to the session
peer."::={ jnxL2tpSessionStatsEntry 59}jnxL2tpSessionStatsDataRxPkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of data packets
received on this session."::={ jnxL2tpSessionStatsEntry 60}jnxL2tpSessionStatsDataRxBytes OBJECT-TYPESYNTAXCounter64
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of data
bytes that were received from the session
peer."::={ jnxL2tpSessionStatsEntry 61}jnxL2tpSessionStatsErrorTxPkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the number of error
transmit packets on the session."::={ jnxL2tpSessionStatsEntry 62}jnxL2tpSessionStatsErrorRxPkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"This object contains the number of error
receive packets on the session."::={ jnxL2tpSessionStatsEntry 63}---- The L2TP Multilink PPP bundle statistics table--jnxL2tpMlpppBundleStatsTable OBJECT-TYPESYNTAXSEQUENCEOF JnxL2tpMlpppBundleStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The L2TP MLPPP bundle status and statistics table. This
table contains the objects that can be used to
describe the current status and statistics of a
single L2TP tunneled multilink PPP bundle."::={ jnxL2tpObjects 5}jnxL2tpMlpppBundleStatsEntry OBJECT-TYPESYNTAX JnxL2tpMlpppBundleStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"An L2TP MLPPP bundle statistics entry."INDEX{ jnxL2tpMlpppBundleStatsBundleID }::={ jnxL2tpMlpppBundleStatsTable 1}
JnxL2tpMlpppBundleStatsEntry ::=SEQUENCE{
jnxL2tpMlpppBundleStatsBundleID
Integer32,
jnxL2tpMlpppBundleStatsNumLinks
Integer32,
jnxL2tpMlpppBundleStatsEndpoint
SnmpAdminString,
jnxL2tpMlpppBundleStatsInputMrru
Integer32,
jnxL2tpMlpppBundleStatsOutputMrru
Integer32}jnxL2tpMlpppBundleStatsBundleID OBJECT-TYPESYNTAXInteger32(1..65536)MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"This object identifies the session's associated
bundle."::={ jnxL2tpMlpppBundleStatsEntry 1}jnxL2tpMlpppBundleStatsNumLinks OBJECT-TYPESYNTAXInteger32(1..8)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object identifies the current number
of links that have joined the bundle."::={ jnxL2tpMlpppBundleStatsEntry 2}jnxL2tpMlpppBundleStatsEndpoint OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object identifies the username
of the MLPPP bundle."::={ jnxL2tpMlpppBundleStatsEntry 3}jnxL2tpMlpppBundleStatsInputMrru OBJECT-TYPESYNTAXInteger32(64..4500)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object identifies the maximum
packet size that the input inteface can
process."::={ jnxL2tpMlpppBundleStatsEntry 4}jnxL2tpMlpppBundleStatsOutputMrru OBJECT-TYPESYNTAXInteger32(64..4500)MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object identifies the maximum
packet size that the output interface can
process."::={ jnxL2tpMlpppBundleStatsEntry 5}END